Somfy action in Link’nX: open, close or position a shutter

A Somfy action in Link’nX prepares a command for a device of a Somfy box, for example a shutter or a blind: open, close, stop, “my” position, or a closure, deployment or orientation percentage. A scenario then runs this action.

Intended for administrators and installers. To control the device from a KNX push button, use the Somfy KNX gateway instead; to react to a device status, use Somfy triggers. A user who only wants to use an existing automation can find and run its scenario.

Before you start

• The box is declared and its discovered devices are saved in the right gateway.

Create the action

1. Open Actions, then Add. In Select an action type, choose Somfy.
2. Fill in Name, required, 64 characters maximum, not only spaces.
3. In Somfy box to control, choose the box. The One box per action hint applies to this form.
4. In Device, choose the shutter, blind or other device saved for this box. For a confirmed URL missing from the list, choose ✎ Enter the URL manually…, then fill in Sub-device URL. Fictitious example: io://0000-0000-0000/1.
5. In Somfy command, choose a command offered for this device, using the table below.
6. If a Value field appears, enter the desired percentage, from 0 to 100. 0 is a usable value, not an empty field. Orientation is also expressed as a percentage, not in degrees.
7. Click the round floppy disk at the bottom right and wait for Success!. The action appears in the list.
8. To automate it, add it to the scenario concerned.

Catalog commands, depending on the device	Value field
Open, Close, Stop, My position	None
Set closure (0-100)	Closure percentage
Set deployment (0-100)	Deployment percentage
Set orientation (0-100)	Orientation percentage

A position setpoint of 0 is not the Stop command: to stop the movement, choose Stop if it is offered. The physical result and the available positions depend on the configured device.

Edit the action

Open the name or the pencil of the action. Review the box, device, command and value before saving. If a window lists affected scenarios, review their names, then click SAVE, or CANCEL. Wait for Updated!. Duplication, the side panel and leaving the form are described in the common actions guide.

• Changing the box requires choosing the device again.
• Changing the device can clear a command that is not offered for the new target: then choose a suitable command and check the remaining value.
• An old saved URL can remain displayed although it is no longer in the discovered list. The form thus preserves the choice, without confirming its availability: check the target before keeping it.
• To act on several boxes, prepare one action per box, add them to the scenario and check each target.

Check the result

Success! confirms that the action is saved. After the scenario runs, watch the device and compare its movement or position with the saved command and value.

Troubleshooting

• The Somfy type does not appear: clear the search, then check the context and the Somfy option. If access is still missing, contact support.
• Some commands have disappeared: the choices follow the known capabilities of the selected device. Check the box and the device, then refresh and save its discovery if needed. Changing the interface language does not change this choice. If the capabilities are not known, a broader catalog can appear: not all its commands necessarily work on your model.
• No Value field after Open: this is normal, this command does not use a percentage. There is no need to enter 0.
• The shutter does not move: saving prepares the action, which acts when the scenario runs. Check the saved target and command, then the box’s discovery status.

Message when saving	Action
Issue with device field selection. At least one value required.	Choose the box in Somfy box to control.
Please provide the Somfy sub-device URL	Choose a device or fill in the manual URL.
Issue with action. You need to add at least one action to the list.	Choose a Somfy command.
Issue with value field. You need to enter a value.	Fill in Value, from 0 to 100.

If the target or its compatibility remains uncertain, contact support before multiplying tests.

Contact support

If these checks are already done, write to support@can-nx.com with the context, the device, the command, any value and the tests carried out. Never send the box’s token.

French labels: Box Somfy à contrôler, Une seule box par action, Équipement, URL du sous-équipement, Commande Somfy, Valeur, Ouvrir, Fermer, Arrêter, Position ‘my’.